Sugar Land TX standing seam metal roof installation

How To Install A Standing Seam Metal Roof

Are you looking for information on Sugar Land TX standing seam metal roof installation? You clicked on the right article. The standing seam roof’s success resides in the seam’s height and integrity. It usually projects 1 “or more over the surface and therefore is higher than most running water. The raw materials were commonly available in the mid-19th century. Standing seam metal roofs became used in almost any architectural style for the most traditional roofs on old houses. An innovative system of metal sheets crimped together in seams that jut an inch or more above the roof.

These are often relatively easy to install, particularly on houses with minimal ridges and valleys. You only need just a few specific hand tools and an old-house restorer average mechanical skills. If the metal roof beauty smites you, here are the basics to get you started on your Sugar Land TX standing seam metal roof installation.

Sugar Land TX standing seam metal roof installation

Sugar Land TX standing seam metal roof installation

Sugar Land TX Standing Seam Metal Roof Installation Preparation Makes Perfect

Be careful to take note of seams on ridges and ends when measuring the metal pans. Start with a clean roof deck. Remove the existing roofing and remove the old bolts, make sure the surface is scrupulously clean of everything that may puncture the new roof or blemish it. Steel-based standing seam roofing is mostly installed on basic houses and secondary roofs over spaced decks or skip sheathing. Make sure the boards are laid with gaps of about 11⁄2 “or so — but all three typically used materials work equally well on closed-board or plywood decks.

The next move for roofers using steel or alloy terne is to underlay them with red rosin paper; with these metals, never use black roofing felt or tar material because the asphalt can destroy them. To prevent the saturated felt from bonding to the metal, copper manufacturers suggest roofing felt underlying topped by a rosin building paper.

In any case, before you start, you can install metal edging along the perimeter of the roof to support the sheet metal’s 1⁄2 “to 1” overhang to prevent water from running back under the edge. For Terne II and galvanized steel use standard, prefabricated steel drip edge; use copper locking strip for copper. Nail the edge every 10 “along the ends and ends and edges of the roof. Anywhere the water flows off. Metal clips nailed on skip sheathing or plywood deck anchor pans and seams.

Sugar Land TX standing seam metal roof installation

Sugar Land TX standing seam metal roof installation

Start Your Sugar Land TX Standing Seam Metal Roof Installation With The Sheets

Every length of sheet metal roofing— called a pan — must be bent to the edges to create seams. Thoughtful project preparation and diligent materials measuring can help to make a pleasant, smoothly performed installation. Sketch your roof’s layout, calculate for symmetrical seams to prevent awkward or excessively narrow panes.

Most old-house roofs are built with less than even dimensions, so be prepared to work the plan from the middle of the roof to split any odd spacing. When you are going to make seams along ridges where two roofs meet, remember to offset the spacing of the pan. So that the seams in one roof meets the center of the pans on the side of the other roof, when you are doing this, you’re not going to have as much metal to bend into a tight, uniform ridge seam.

How To Make Pans

To make the pans, measure from 4 “above the roof ridge (to allocate metal to a seam). And also 1” beyond the edge of the roof, then cut the metal with metal shears or tin snips to this dimension. Next, bend along the broad edges of the pan, 1⁄2 “on one side and 1” on the other.

(On a simple gable roof, the outboard first and last pans should have an edge–the one that runs along the roof rake–bent down 1 “so that it can be crimped to the edge of the drip or locking strip.) Than ends should be cut and crimped across the edge of the metal drip where they cross the eaves and rakes of the roof.

The tools designed for this purpose, called pan benders, come in various styles— typically plain universal types that function like a giant pair of locking pliers, and patent types that use foot pedals to speed up the bending process. On some, you will first set the jaws by adjusting the stops and bolts to the correct seam depth.

Bending an edge in two stages pays off. First, bend the whole edge to around 45 degrees, then return to bend to the maximum 90 degrees, take pains to make sure you’ve got an excellent straight metal crease. Do not discard tiny bits of scrap metal; instead, cut them into strips of 1″ by 21⁄2” to make clips to fasten the pans to the deck.

Installing Pans

You will begin laying the roof when you have all your pans bent. (When working on old homes, specific roofers tend to start putting pans in the center of the deck and work out to the ends and make sure the pans are lie square.) Next, secure the pan to the deck by bending clips over the upright edge every 10 “or so, and then nail the clips to the deck. Again, maintaining all the creases are sharp; with the adjacent pan, they will have to be folded to a seam.

When the end pan is secured, it’s essential to bend the edges at the roof perimeter around the locking strip or drip edge. Using locking pliers, you will easily crimp the metal together on the rake. However, on the bottom edge, at the up-bends to create the standing seams, you’ll need to cut the pan back 1 “or so. Certain patent roofing tongs may be used to make seams as well as bending up edges.

Bend Edge of Drip

You should either bend the metal around the edge of the drip or lock strip. You will start laying the rest of the roof and make seams using the installed end pan. Take a typical pan and lay it next to the 1 1/2 “edge that you just clipped down with the “edge. Fine-tune the position, so the top and bottom edges align with the previous pan to make sure that the pan is snug against the deck. Then clamp both pans with locking pliers together every 2 ”.

Using a seaming iron, start seaming between the first two locking pliers on top of the roof. Place the iron against the upturned 1 “metal edge and bend the 11⁄2” metal edge over the iron to 90 degrees using a soft-faced mallet, sliding the iron along as you hammer—this way, when you have bent around 2′ of the seam. Remove the iron and tap another 45 degrees down the metal using just the hammer. Furthermore, move the iron to the opposite side of the seam. Place the iron against the metal and hammer the seam and make sure it is closed into a tight crimp. Making sure that the longer metal edge covers the shorter edge entirely so that all the clips are well covered and crimped too.

Next Step

A seaming iron is a low-tech device that is made by a welder. Using one side to form the first bend, then complete the double lock on the other side. At this point, you’ve completed a bend, but to connect the pans in a double-lock standing seam, you’ll need to repeat that process.

Begin in the middle of the section you have just completed, place the iron’s shorter side against the same edge where you began, and bend the metal down to 90 degrees. Continue as much seam as possible between the locking pliers with the remaining of the steps. Then continue on to do another section. You can remove one of the pliers after you have completed an adjacent seam section and fill in the seam underneath it.

If you’ve mastered the simple methods of bending and seaming, you may use those skills to create roof and hip ridges, valleys, and other details that might be necessary on more complex roofs. Once you are done, immediately paint your Terne II roof in a classic shade of black, red, green, or silver. Then, stand back and admire the conventional lines of a standing seam roof.

Houston TX standing seam metal roofing

Let All-Star Roof Systems be your go-to contractor!

All-Star Roof Systems

Need help with your Sugar Land TX standing seam metal roof installation? We are Houston’s first option for metal roofs, aluminum roofing, aluminum shake and shingle, and standing seam roofs. All-Star Roof System has been the primary metal roofing contractor for approximately 50 years. All Star Roofing Systems, Inc. is an A+ accredited member of the Better Business Bureau.

As a roofing company, we provide multiple metal roofing systems and specialize in roof repairs. Are you tired of your shingle roof in Sugar land, TX? Contact us for a metal roof installation. We install a different type of metal roofing compared to our competitors.

Our sales personnel have significant experience in dealing with all insurance companies. All of our roof installers are certified with at least 20 years ‘ experience. You can rest assured, with our help, that your roof is better than new. We have all you need for the job, from commercial to residential use. That means we’re bringing you the parts, roof materials, products, and installation at a low rate. Call us for a free estimate at (281) 987-9000 and allow us to help you with your Sugar Land TX standing seam metal roof installation.

Fun Facts About Sugar Land, Texas

  1. Sugar Land has well over 560 acres of developed parkland.
  2. The Sugar Land Town Square used the 3D projection technology used in the 2010 Olympics on New Year’s Eve 2009.
  3. In 2013, Sugar Land now boasted a population of 84,511.
  4. To learn more about Sugar Land, Texas, click here.

WOULD YOU LIKE TO LEARN MORE?

If you would like to learn more or to discuss
your project just give us a shout to get started.
There is no obligation.

Contact Us

Houston Metal Roofing Systems Site Map

Call Us
Email Us
Free Quote